What is the technical standard for repairing the heat transfer oil circulating oil pump bearing?

September 08, 2020

First, the rolling bearing 1, the bearing and the shaft are matched by the base hole, and the bearing and the outer casing are made by the base shaft. The values ​​of bearing dimensional tolerance and rotation accuracy are in accordance with GB307-84. What is the technical standard for repairing the heat transfer oil circulating oil pump bearing?
1. The bearing and the shaft are matched by the base hole, and the bearing and the outer casing are made by the base shaft.
The values ​​of bearing dimensional tolerance and rotation accuracy are in accordance with GB307-84.
2. The journal and the inner hole of the bearing housing matched with the bearing are in accordance with the provisions of GB1031-83, the rall roughness Ra value is less than 1.6μm, and the hole roughness Ra of the bearing housing is less than 2.5μm.
3. When manufacturing bearing rings and rollers with GCr15 and ZGCr15 steel, the hardness of the ferrule and roller should be 61~65HRC; when made of GCr15SiMn and ZGCr15SiMn steel, the hardness value should be 60~64HRC. The hardness inspection method and the uniformity of the hardness of the same part are as specified in JB1255.
4. Check the radial clearance and axial clearance of the bearing to meet the requirements of GB4604-84.
5. The inner and outer ring raceways of rolling bearings should be free from flaking and severe wear. There should be no cracks in the inner and outer rings; the balls should be free of wear, the cages are not seriously deformed, there is no abnormal noise and vibration when rotating, and should stop gradually when stopping.
6. For the C-class tolerance tapered roller bearing, the contact precision between the roller and the ferrule raceway shall be checked under the action of a certain load. The contact marks shall be continuous, and the contact length shall not be less than 80 of the roller busbar.
2. Sliding bearing 1. Heat-conducting oil circulating oil pump For the radial thick-walled tile 1, the bearing clearance and the bearing shell interference are measured by the pressure lead method, the lifting shaft method or other methods. The shaft clearance meets the requirements, and the tile shell interference should be 0 to 0.02 mm.
2 Check all parts, there should be no damage and cracks, and the bearing bush should be free from peeling, pores, cracks, channels and partial wear.
The contact condition between the 3 bush and the journal is checked by the coloring method, and the inspection angle should be 60° to 90° (the lower limit of the rotation speed is higher than 1000r/min, and the upper limit of the rotation speed is less than 1000r/min). Uniform contact is required within the contact range, and there should be 2 to 4 contact points per square centimeter. If the contact is poor, scraping must be performed. Botou Taibang Pump & Valve Manufacturing Co., Ltd. 4 clean the bearing box, the oil holes are unblocked, and there must be no cracks or leakage.
The 5 watt back and the bearing housing should be closely and evenly bonded, and the coloring method should be used to check that the contact area is not less than 50.
2. The heat transfer oil circulation oil pump should be firmly and tightly combined with the alloy layer and the tile shell of the radial thin-walled tile 1 bearing bush, and there should be no delamination or shelling. The surface of the alloy layer and the surface of the two half-slabs should be smooth and flat, and defects such as cracks, pores, heavy skin, slag inclusions and bumps are not allowed.
The surface of the inner wall of the 2 watt back and the bearing housing should be closely and evenly fitted. The parking area is checked by the coloring method. The inner diameter is less than 180mm, the contact area is not less than 85, and the inner diameter is greater than or equal to 180mm. The contact area is not less than 70.
The matching clearance and contact condition of the 3-axis bush and the journal are guaranteed by the machining precision. The contact area is generally not allowed to be scraped. If the axial contact is uneven, it can be slightly trimmed.
4 After assembly, check with a 0.02mm feeler gauge at the mid-section, and it should not be qualified.
3. The heat transfer oil circulating oil pump shall have no wear, deformation, crack, scratch, delamination, crushing and burn defects for the thrust bearing 1 bearing bush; the printed mark shall be uniform at the contact with the thrust plate, and the contact area shall be not less than 70 and The entire circumference of each tile is evenly distributed; the thickness difference of the same group of tiles should be no more than 0.01mm, the tile babbitt should be rounded into the oil wedge in the direction of rotation to facilitate the entry of lubricating oil; the back bearing surface is smooth and smooth.
2 Adjust the gasket to be smooth, flat, non-flexible, and use a layer of gasket with a thickness difference of not more than 0.01mm.
3 After the bearing cap is assembled, the thrust bearing clearance is repeatedly measured by the push shaft method, and the value should be within the required range. In this way, the thrust bearing clearance measured on the side of the shaft displacement probe must be the same, and the indication zero of the displacement probe should be adjusted as specified.
4 bearing shell horizontal joint surface is tight, not bad. The oil hole for measuring the oil temperature is aligned with the tile cover eye and is not skewed. The oil hole is clean and unobstructed.













Http://news.chinawj.com.cn What is the technical standard for repairing the heat transfer oil circulating oil pump bearing? Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn What is the technical standard for repairing the heat transfer oil circulating oil pump bearing?

Hexagon wire netting also named chicken wire, chicken mesh, hencoop mesh and turtleback mesh.

Weaving pattern: straight twist, reverse twise, and double-direction twist.

It can be weaved after galvanized or galvanized after weaving.Galvanized can be electric galvanized or hot dipped.

hexagonal wire netting

Hexagonal Wire Mesh

Application:it used wide in building,oil, chemical industry, breed, plant protection , food processings reinforce guard 

and heat preservation , for example: make insulated net wall ,boiler cover etc.

Stainless Hexagonal Wire Mesh

Stainless Hexagonal Wire Mesh,Hexagonal Shape Expanded Metal,Hexagonal Wire Mesh,Galvanized Hexagonal Wire Mesh

Anping Shengjia Hardware Mesh Co.,LTD , https://www.oilshaleshakerscreen.com